Iota I-162 User Manual download pdf

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C. power

is supplied to the unit.

2. CAUTION – This ﬁxture provides more than one power supply output source. To reduce the risk of electrical

shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by disconnect

ing the unit connector.

3. CAUTION – The integral, high temperature Ni-Cad battery is replaceable. To replace the battery, disconnect the

unit connector and remove both switched and unswitched A.C. power to the ﬁxture. Remove the lid screw and

open the lid to expose the battery. Unplug the battery connector and replace with part number 44203-412 (14.4V

Ni-Cad battery only). Recycle or dispose of the used nickel-cadmium battery properly

4. DO NOT USE OUTDOORS. The I-162 is for use with grounded, UL Listed, damp location rated, indoor ﬁxtures.

Do not use in heated air outlets or hazardous locations.

5. The I-162 requires an unswitched A.C. power source of either 120 or 277 volts. Properly cap the unused A.C. lead.

6. When the I-I62 is installed on the same branch circuit, refer to Illustration 2, Figures A and B for input wiring. When

installed on separate branch circuits, refer to Illustration 2, Figures C and D for input wiring. Per NEC, the I-I62 and

A.C. ballast must be on the same panel board.

7. Do not mount near gas or electric heaters.

8. The I-162 should be mounted in locations and at heights where it will not readily be subjected to tampering by

unauthorized personnel.

9. The I-162 mounts on top of the ﬁxture or adjacent to the ﬁxture on an optional T-bar mounting bracket.

10. The I-162 will cold strike and operate two 4′ instant start, rapid start, U shape or circline ﬂuorescent lamps, T8

through T12 ﬂuorescent lamps, two 24W-50W long compact lamps, or two 54W T5 ﬂuorescent lamps.

11. The I-162 operates lamps as follows:

Two 4 ′ T8-T12 lamps, two 24W-50W long compact, or two 54W T5 lamps for 90 minutes.

12. Suitable for use in damp locations.

13. For use in 0° C minimum, 50° C maximum ambient temperatures.

14. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition, void

warranty, and result in non-compliance with UL speciﬁcations.

15. Do not use this equipment for other than intended use.

16. Install in accordance with the National Electrical Code and local regulations.

17. Installation and servicing should be performed by qualiﬁed personnel.

18. Lighting ﬁxture manufacturers, electricians, and end-users need to ensure product system compatibility before

ﬁnal installation.

SAVE THESE INSTRUCTIONS

I-162

SERIES AC

PARALLEL OPERATION

EMERGENCY

LIGHTING EQUIPMENT

INSTRUCTION MANUAL

P.O. BOX 11846 TUCSON, AZ 85734

(520) 294-3292 • FAX (520) 741-2837

www.iotaengineering.com

1 2 3 4

Summary of Contents

Page 1 - INSTRUCTION MANUAL

IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL

Page 2 - INSTALLATION INSTRUCTIONS

Page 27/8" BUSHINGPLASTIC TUBECHARGE INDICATOR LAMPBALLAST CHANNELCOVERFLEX CONDUITFIXTURE LENSINSTALLATION INSTRUCTIONSCAUTION: Before install

Page 3 - TESTING & MAINTENANCE

Page 36. LABELS Attach the appropriate labels adjacent to the Test Switch and Charge Indicator. Annotate Re-lamping label for lamp type and wattage.

Page 4 - TYPICAL WIRING DIAGRAMS

Page 4WHITECOMMONUNSWITCHEDLINEORG (277V)BLK (120V)CONNECTORBLUEBLUE/WHTVIOLETVIO/GREYBRNWHITEBLACKBLUEBLUEREDREDYELLOWYELLOWLAMP*LAMP*A.C.BALLASTBRN/

Comments to this Manuals

No comments

Iota I-162 User Manual

Browse online or download User Manual for Power suppliers Iota I-162. IOTA I-162 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power suppliers Iota I-162