Iota I-13-EM-B User Manual download pdf

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C.

power is supplied to the unit.

2. CAUTION – This ﬁxture provides more than one power supply output source. To reduce the risk of electrical

shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by discon

necting the unit connector.

3. CAUTION – This is a sealed unit. The integral, high temperature Ni-Cad battery is not replaceable. Replace

the entire unit when necessary and recycle or dispose of the nickel-cadmium battery properly.

4. DO NOT USE OUTDOORS. The I-13-EM-B is for use with grounded, UL Listed, damp location rated, indoor

ﬁxtures. Not for use in heated air outlets or hazardous locations.

5. The I-13-EM-B requires an unswitched A.C. power source of either 120 or 277 volts. Properly cap the unused

A.C. lead.

6. When the installation is complete, switch the A.C. power on and join the I-13-EM-B unit connector.

7. Do not mount near gas or electric heaters.

8. The I-13-EM-B should be mounted in locations and at heights where it will not readily be subjected to tamper

ing by unauthorized personnel.

9. The I-13-EM-B will cold strike and operate one 5W, 7W, or 9W, twin tube, double twin tube, 180ma or 13W

twin tube, double twin tube, 285ma ﬂuorescent lamp, each with a single lampholder per lamp.

10. The I-13-EM-B is for use with ﬂuorescent downlight ﬁxtures.

11. Suitable for use in damp locations and in enclosed and gasketed ﬁxtures.

12. When used in conjunction with enclosed and gasketed ﬁxtures, the I-13-EM-B is suitable for mounting in the

ballast compartment only.

13. For use in 0° C minimum, 50° C maximum ambient temperatures.

14. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition, void

warranty, and result in non-compliance with UL speciﬁcations.

15. Do not use this equipment for other than intended use.

16. When the installation is complete, switch the A.C. power on and join the I-13-EM-B unit connector..

Install in accordance with the National Electrical Code and local regulations.

17. Installation and servicing should be performed by qualiﬁed personnel.

18. Lighting ﬁxture manufacturers, electricians and end users need to ensure product system compatibility before

ﬁnal installation.

SAVE THESE INSTRUCTIONS

I-13-EM-B

INSTRUCTION MANUAL

SERIES D

COMPACT LAMP

EMERGENCY

LIGHTING EQUIPMENT

P.O. BOX 11846 TUCSON, AZ 85734

(520) 294-3292 • FAX (520) 741-2837

www.iotaengineering.com

1 2 3 4 5

Summary of Contents

Page 1 - I-13-EM-B

IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed, including the following:READ AND FOLLOW ALL S

Page 2 - INSTALLATION INSTRUCTIONS

Page 2INSTALLATION INSTRUCTIONSCAUTION: Before installing, make certain the A.C. power is off and the I-13-EM-B unit connector is disconnected.1.

Page 3 - TESTING & MAINTENANCE

Page 35. LABELS Attach the appropriate labels adjacent to the Test Switch and Charge Indicator. Annotate Re-lamping label for lamp type and wattage

Page 4 - TYPICAL WIRING DIAGRAMS

Page 4UNITCONNECTORCHARGEINDICATORTESTSWITCHRED ORRED/BLK (+)WHT/BLKBLK (120V)ORG (277V)WHITEBLUE/WHTBLUEYELLOWYEL/BLKBLUEBLACKUNSWITCHED LINECOMMONSW

Page 5

Page 56. TWO LAMP PARALLEL HIGH POWER FACTOR MAGNETIC BALLAST8. TWO LAMP SERIES HIGH POWER FACTOR MAGNETIC BALLASTUNITCONNECTORCHARGEINDICATORRED ORRE

Comments to this Manuals

No comments

Iota I-13-EM-B User Manual

Browse online or download User Manual for Power suppliers Iota I-13-EM-B. IOTA I-13-EM-B User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power suppliers Iota I-13-EM-B