Iota I-40 User Manual download pdf

I-40

TBTS SERIES D

EMERGENCY

LIGHTING EQUIPMENT

INSTRUCTION MANUAL

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed, including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C.

power is supplied to the unit.

2. CAUTION – This ﬁxture provides more than one power supply output source. To reduce the risk of electrical

shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by discon-

necting the unit connector.

3. CAUTION – This is a sealed unit. The integral, high temperature Ni-Cad battery is not replaceable. Replace

the entire unit when necessary and recycle or dispose of the nickel cadmium battery properly.

4. DO NOT USE OUTDOORS - The I-40 is for use with grounded, UL Listed, damp location rated, indoor

ﬁxtures. Not for use in heated air outlets or hazardous locations.

5. The I-40 requires an unswitched A.C. power source of either 120 or 277 volts. Properly cap the unused

A.C. lead.

6. The I-40 and A.C. ballast must be on the same branch circuit.

7. Do not mount near gas or electric heaters.

8. The I-40 should be mounted in locations and at heights where it will not readily be subjected to tampering by

unauthorized personnel.

9. The I-40 will cold strike and operate one 2´ through 4´ (20-40W) instant start, rapid start, U shape or circline,

T8 through T12 ﬂuorescent lamps, including energy saving and long compacts for 90 minutes at reduced light

output.

10. The I-40 is suitable for mounting in the ballast compartment or on top of the ﬁxture. For top mount, order op-

tional mounting kit TMK-80. When used in conjunction with enclosed and gasketed ﬁxtures, the I-40 is suitable

for mounting in the ballast compartment only.

11. The I-40 is compatible with all A.C. magnetic and electronic ballasts including multiple lamp ballasts with one

lamp operating in the emergency mode.

12. Suitable for use in damp locations and in enclosed and gasketed ﬁxtures.

13. For use in 0° C minimum, 50° C maximum ambient temperatures.

14. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

15. Do not use this equipment for other than intended use.

16. Install in accordance with the National Electrical Code and local regulations.

17. Installation and servicing should be performed by qualiﬁed personnel.

18. Lighting ﬁxture manufacturers, electricians, and end-users need to ensure product system compatibility before

ﬁnal installation.

SAVE THESE INSTRUCTIONS

P.O. BOX 11846 TUCSON, AZ 85734

(520) 294-3292 • FAX (520) 741-2837

www.iotaengineering.com

1 2 3 4

Summary of Contents

Page 1 - IMPORTANT SAFEGUARDS

I-40TBTS SERIES DEMERGENCYLIGHTING EQUIPMENTINSTRUCTION MANUALIMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should alw

Page 2 - INSTALLATION INSTRUCTIONS

Page 27/8" BUSHINGFIXTUREBALLAST CHANNEL COVERPLASTIC TUBETBTSFIXTURE LENSINSTALLATION INSTRUCTIONSCAUTION: Before installing, make certain the

Page 3 - TESTING & MAINTENANCE

Page 35. BALLAST WIRING BLOCK DIAGRAM6. LABELS Attach the appropriate labels adjacent to the TBTS. Annotate Re-lamping label for lamp type and wat

Page 4 - TYPICAL WIRING DIAGRAMS

Page 4TYPICAL WIRING DIAGRAMSFor wiring diagrams of ballasts not shown, consult our Customer Service.Rev. 07151368440-4031. ONE LAMP RAPID START BALL

Comments to this Manuals

No comments

Iota I-40 User Manual

Browse online or download User Manual for Power suppliers Iota I-40. IOTA I-40 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power suppliers Iota I-40