Iota I-880 User Manual

Browse online or download User Manual for Power suppliers Iota I-880. IOTA I-880 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 5
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. CAUTION To prevent electrical shock, do not mate unit connector until installation is complete and A.C. power
is supplied to the unit.
2. CAUTION This fixture provides more than one power supply output source. To reduce the risk of electrical
shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by disconnect-
ing the unit connector.
3. CAUTION This is a sealed unit. The integral, high temperature Ni-Cad battery is not replaceable. Replace the
entire unit when necessary and recycle or dispose of the nickel-cadmium battery properly.
4. DO NOT USE OUTDOORS. The I-880 is for use with grounded, UL Listed, indoor fixtures. Not for use in heated
air outlets or hazardous locations.
5. The I-880 requires an unswitched A.C. power source of either 120 or 277 volts. Properly cap the unused A.C.
lead.
6. Do not mount near gas or electric heaters.
7. The I-880 should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
8. The I-880 is suitable for mounting in the ballast compartment or on top of the fixture. For top mount, order op-
tional mounting kit TMK-80.
9. The I-880 will cold strike and operate one 2–8 or two 2–4 instant start, rapid start, U shape or circline, T8
through T12 fluorescent lamps, or one 2–4 28W or 54W HO or VHO fluorescent lamp, including energy saving
and long 4 pin compact lamps for 90 minutes.
10. The I-880 is compatible with most A.C. ballasts (including multiple lamp) as follows:
Magnetic ballasts – either one or two lamp emergency operation.
Electronic ballasts – one lamp emergency operation, consult Customer Service for two lamp emergency opera-
tion wiring diagrams.
11. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
12. Do not use this equipment for other than intended use.
13. Install in accordance with the National Electrical Code and local regulations.
14. Installation and servicing should be performed by qualified personnel.
15. Lighting fixture manufacturers, electricians, and end-users need to ensure product system compatibility
before final installation.
SAVE THESE INSTRUCTIONS
I-880
SERIES D
EMERGENCY
LIGHTING EQUIPMENT
INSTRUCTION MANUAL
THIS UNIT CONTAINS A
RECHARGEABLE NICKEL-
CADMIUM BATTERY. PLEASE
RECYCLE OR DISPOSE OF
PROPERLY.
P.O. BOX 11846 TUCSON, AZ 85734
(520) 294-3292 FAX (520) 741-2837
www.iotaengineering.com
Page view 0
1 2 3 4 5

Summary of Contents

Page 1 - INSTRUCTION MANUAL

IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed, including the following:READ AND FOLLOW ALL S

Page 2 - INSTALLATION INSTRUCTIONS

Page 27/8" BUSHINGFIXTUREBALLAST CHANNEL COVERPLASTIC TUBECHARGE INDICATORLIGHTFIXTURE LENSINSTALLATION INSTRUCTIONSCAUTION: Before installing,

Page 3 - TESTING & MAINTENANCE

Page 35. INSTALLING THE TEST SWITCH The test switch should be mounted on the ballast channel cover of a recessed troffer, or on the side of a strip

Page 4 - TYPICAL WIRING DIAGRAMS

Page 4UNSWITCHEDSWITCHED ORUNSWITCHEDLINECOMMONORG (277V)BLK (120V)WHITE*LAMP*LAMP*AC / EMERGENCYBLACKWHITEBLUEBLUEREDBLUEBLUE/WHTRED/WHTREDYELLOWUNIT

Page 5 - ADDITIONAL WIRING DIAGRAMS

Page 5ADDITIONAL WIRING DIAGRAMSFor wiring diagrams of ballasts not shown, consult our Customer Service.1. THREE LAMP RAPID START BALLAST3. FOUR LAMP

Comments to this Manuals

No comments